[Mar 09, 2022] Free CIP Level 2 NACE-CIP2-001 Official Cert Guide PDF Download
NACE NACE-CIP2-001 Official Cert Guide PDF
NEW QUESTION 44
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. mill scale.
- C. dirt.
- D. snow, ice or water.
Answer: B
NEW QUESTION 45
Generally for safety considerations, waterjetting hose connections use
- A. a long wand.
- B. a whip-lock device.
- C. an oil/water separator.
- D. filters.
Answer: B
NEW QUESTION 46
You can use magnifiers to examine all of the following EXCEPT
- A. Blisters
- B. Surface cleanliness
- C. Mill scale
- D. Surface profile
Answer: B
NEW QUESTION 47
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It contains biocide
- B. The floating structure is stationary
- C. It doesn't contain biocide
- D. It will result in a very slippery surface
Answer: A
NEW QUESTION 48
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Ultra Sonic DFT Gauge
- B. Tooke Gauge
- C. Magnetic Gauge
- D. Eddy Current Gauge
Answer: B
NEW QUESTION 49
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept assignment without hesitation
- B. Advise the prospective employer that you cannot accept the position
- C. Meet with the prospective employer to scope of your role
- D. Review the NACE Attestation prior to making a decision
Answer: D
NEW QUESTION 50
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. in a well ventilated area separate from the work place.
- C. in a refrigerated warehouses
- D. wherever it is convenient
Answer: B
NEW QUESTION 51
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method B - Cross Hatch
- C. Method A - Cross Hatch
- D. Method A - X Cut
Answer: D
NEW QUESTION 52
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Acid etching
- C. Sacking
- D. Stoning
Answer: C
NEW QUESTION 53
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Use the correct solvent
- C. Record the two end points identified in the standard
- D. Record the highest value attained
Answer: C
NEW QUESTION 54
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Call your supervisor
- B. Ignore the additional requirement
- C. Enforce the additional requirement
- D. Request clarification from the specifier
Answer: C
NEW QUESTION 55
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Schedule the remedial work
- C. Develop a survey plan
- D. Evaluate the coatings performance
Answer: A,B,C,D
NEW QUESTION 56
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION 57
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 2-Layer Polyethylene (PE)
- B. Fusion Bonded Epoxy
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION 58
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Coalescence
- C. Co-Reaction
- D. Oxidation
Answer: B
NEW QUESTION 59
......
Free NACE-CIP2-001 Exam Dumps to Improve Exam Score: https://preptorrent.actual4exams.com/NACE-CIP2-001-real-braindumps.html